Concrete cutting in Edwardsville IL - clean openings with the dust kept down
Need an opening, a pipe hole or a bad section out of your slab? We scan, cut straight and keep the dust and slurry contained.

How do you cut concrete without hitting what's inside it?
Concrete cutting in Edwardsville means sawing straight lines through a slab or wall for an opening, a removal or a clean edge. Coring means drilling a round hole with a hollow diamond bit for a pipe, a conduit or an anchor.
Usually you've got a project planned and the concrete is in the way. A plumber needs a trench through the basement floor, a sunken section of driveway has to come out, or a vent line needs a hole through a wall. The cut itself is the quick part. Most of the care goes into finding what's inside the concrete first and deciding where the dust and water go, because concrete is easy to cut and impossible to uncut.
The price moves with how thick the concrete is, how many feet of cut or how many holes you need, whether it's a floor or a wall, how much steel is inside and how easy the spot is to reach. The schedule mostly turns on things outside the saw, like utility marks, a permit for street work or an engineer's sign-off on anything structural. My estimate spells out what we'll cut and how, in plain words.
What matters on a concrete cutting job
Before we cut anything, it helps to know where the dust goes, where the water goes and whether new concrete is part of the plan, because each one changes how we set up.
A clean edge for new concrete
When part of a slab has to go, we saw a straight line instead of breaking it out ragged. That way a new concrete driveway or patio section has a square, solid edge to meet.
Dust kept down at the saw
Cutting concrete throws silica dust, which you don't want in your lungs or your house, so we cut wet or run a vacuum on the saw. Ask any crew you're comparing how they handle it.
Slurry caught, not hosed off
Wet cutting turns that dust into gray slurry, a cement soup that stains whatever it settles on. We catch it instead of washing it across your yard or down the driveway.
Joints cut on time in new slabs
Control joints are shallow saw cuts that give a new slab a straight place to crack, and they should be cut within 4 to 12 hours after finishing. Concrete is going to crack, so we plan that cut with the pour and tell it where.
Concrete cutting questions we get
How much does concrete cutting cost in Edwardsville?
There's no flat price, and I'll give you a written number once I've seen the spot. Several cored holes price differently than one long saw line, indoor work takes more setup to protect the room, and the cut pieces have to be broken up and moved. Call (618) 800-9951 and I'll come take a look.
What is the best way to avoid hitting rebar or wires when cutting concrete?
Scan the concrete first, and we scan before every cut or core. The scan looks for rebar, the steel bars that hold a slab together, along with post-tension cables, which are steel strands pulled tight inside some slabs, and live electrical conduit. It takes most of the guessing out, but it can't promise a spot is completely clear, so I'll tell you what it shows and what it can't.
How do I know if a concrete cut needs a structural engineer?
Ask the structural engineer for your building, because any structural opening, or any cut through structural steel, needs that engineer's plan. Bring them in before the cut goes on the calendar. If your cut goes through anything structural, we wait for the engineer's sign-off before the saw comes out.
Do I need a permit to cut a street or alley in Edwardsville?
Yes, breaking concrete or other pavement in any street or alley in the city takes a Right of Way Excavation Permit from the city's Director of Public Works or City Engineer. We check with the city, village or county office for every address before we start, handle the permit paperwork our work needs and set up inspections as the job goes.
Does concrete work in Edwardsville's historic district or unincorporated Madison County need approval?
Any exterior work on a property in the City Historic District, or on a landmark property, needs approval first, and you can call 618-692-7535 to learn whether review applies to your house. Out in unincorporated Madison County, the county's Building & Zoning Department runs permits, so the contractor applies with plans first and an inspector checks the work at set stages.
Do I need to call JULIE before concrete cutting?
If the job involves digging, yes, because Illinois law requires homeowners and professional excavators to call JULIE at 811 at least two working days before digging. The work then has to start within 14 calendar days of that call. On our jobs, we get the utilities marked before anyone digs.
Why homeowners here call Edwardsville Concrete for cutting
Concrete takes a lot of work to put down and a lot more to fix after a careless cut, so we plan every cut before we make it.
The owner writes your estimate
I come out, look at the spot and write the estimate myself, and I'm on site with our crew when we pour.
Doing this since 2023
I started Edwardsville Concrete in 2023 after teaching myself on small jobs and learning the rest one pour at a time.
Licensed and insured
That matters on cutting work, where a saw, water and a lot of heavy concrete are all at your house at once.
Both sides of the river
We're based in Edwardsville and work in the cities around it in Illinois and Missouri, from Glen Carbon to Spanish Lake.
Satisfaction guaranteed on every job
That's our promise, so call (618) 800-9951 or send the form, and I'll come take a look at what needs cutting.
Get your concrete cut planned right
Have the address, where the cut or hole goes, its rough size and a few photos handy, and that first call gets your job moving sooner.
What happens after you call about concrete cutting?
We plan every cut around your house, what's inside the concrete and what your local office wants, before the saw ever starts.
Call or send the form
Call (618) 800-9951 or send the form, and we'll set up a time for me to come out and see the spot.
I look at the spot
I measure, check what's around the spot and where the water will run, and look for anything that makes the cut structural or tricky.
A written estimate
I write up what we'll cut and how, in plain words, so you know exactly what you're agreeing to before anything starts.
Permits, cut and walk-through
We handle permits and utility marks, and street work needs 48 hours' notice to Public Works, not counting weekends or holidays. Then we scan, cut and walk the job with you.
